Advanced Materials For a Stronger Tomorrow
Composite materials supplier · India

Everything that goes
into a composite.

Skyrbon supplies the full layup: fibres, matrix, core, prepreg and consumables. One supplier for every layer, from the first ply to the vacuum bag.

Reinforcement

Fibres

The part that carries the load. Supplied as tow, fabric, tape and mat, in the weave and weight your laminate calls for.

Roll of woven carbon fibre fabric

Carbon

Tow from 1K to 24K. Unidirectional, plain, twill and satin weaves. Multiaxial fabrics. Standard to high modulus.

Roll of woven glass fibre fabric

Glass

E-glass and S-glass. Direct rovings, woven roving, chopped strand mat, stitched and woven fabrics.

Roll of woven aramid fabric

Aramid

Para-aramid fabrics in plain and twill weave, for impact and abrasion resistance.

Also on request: carbon/aramid and carbon/glass hybrid weaves, basalt fabrics, chopped and milled fibre.

Resin wetting out carbon fabric
Resin systems

Matrix

The resin that binds the fibre and passes load from one filament to the next. Matched to your process and cure.

  • EpoxyLaminating, infusion and tooling systems, room-temperature and heat cure
  • Vinyl esterChemical-resistant and marine laminates
  • PolyesterGeneral-purpose and gelcoat-backed GRP work
  • HardenersSlow, medium and fast curing agents to set your pot life
  • Gelcoats and adhesivesSurface coats, structural adhesives, fillers and thickeners
Sandwich structure

Core

Put a light core between two skins and a panel gets far stiffer for almost no added weight.

Cutaway of a sandwich panel: carbon skins bonded to an aluminium honeycomb core whose cells run through the thickness
  • HoneycombAluminium and aramid-paper, in a range of cell sizes
  • PVC foamClosed-cell structural foam, plain, scored or perforated
  • PET foamThermoformable and recyclable structural foam
  • PMI foamHigh-temperature foam for prepreg cure cycles
  • Balsa and core matEnd-grain balsa and bulker mats for hand layup
Pre-impregnated

Prepreg

Fibre already impregnated with resin at a controlled ratio. Cut it, lay it up, cure it.

−18 °CPrepreg is stored frozen and has a limited out-life at room temperature. Ask us for shelf life and out-life with every roll.
  • Carbon prepregUnidirectional tape and woven fabric, in a range of areal weights
  • Glass prepregWoven and unidirectional glass in epoxy
  • Aramid prepregWoven aramid for impact-critical skins
  • Tooling prepregFor composite moulds that match the part's expansion

Cure: autoclave systems and out-of-autoclave, vacuum-bag-only systems.

Vacuum bagging and infusion

Consumables

Everything between the tool and the vacuum pump, shown here in the order it goes down.

Vacuum−0.90bar
  1. Bagging film + sealant tapeSeals the layup to the tool
  2. Breather and bleederLets air out, soaks up excess resin
  3. Release filmPerforated or solid
  4. Peel plyLeaves a clean, bondable surface
  5. Your laminateFibre, matrix, core or prepreg
  6. Tool + release agentWax, PVA and semi-permanent systems
  • Infusion meshCarries resin across the part
  • Spiral wrap and hoseResin feed and vacuum lines
  • Vacuum valves and connectorsThrough-bag ports and fittings
  • Flash tapeHolds films and plies in place
  • Mould sealers and cleanersPrepare the tool before release
End uses

What it becomes

The same five families end up in very different parts. Four examples, with the materials that go into each.

Moulded carbon fibre body panel

Body panels

Carbon prepreg, tooling prepreg, release film, bagging film

Carbon fibre sheets, tubes and box sections

Sheets, tubes and profiles

Carbon fabric, epoxy, peel ply

Carbon fibre shell seat

Seats and sports goods

Carbon and aramid fabric, epoxy, release agent

Wind turbines on a ridge

Wind turbine blades

Glass fabric, PET foam and balsa core, infusion mesh

Process finder

Not sure what you need?

Tell us how you build and we list what the job needs. Add the whole kit to your enquiry in one tap.

Get a quote

Enquiry

Tap the + on any material above, or pick from the list here. The enquiry writes itself. Send it on WhatsApp or by email.

  1. Pick your materialsTap the + on anything you need, or add a process kit.
  2. Add specs, size and dateGSM, weave, resin, core density, dimensions, quantity and when you need it.
  3. Send itOn WhatsApp or by email. We reply with a quote.

Specification Fill in what you know. We'll advise on the rest.

Size and quantity

Delivery and contact


        
        

Goes to WhatsApp +91 75795 55565 or [email protected]

About us

Skyrbon

Everything that goes into a composite.

One source. Every layer. Every application.

From materials supplier to composite solutions partner.

Helping engineers, manufacturers and innovators source, select and build better composite structures.

Our vision

To be India's most dependable single source for composite materials, where anyone who builds with composites can get every layer from one place.

Leadership

Gautam Pandey

Leads finance and compliance.

Devavrat Raval

Leads sales and operations.

Contact us

Contact

Call or email our sales team, or send us the enquiry above.

Email [email protected]
Registered office
Skyrbon Private Limited
201, 2nd Floor, Shreeji Chambers
Tata Road No. 2, Roxy Cinema, Opera House
Girgaon, Mumbai 400004
Drafting your enquiry